Solution | How KJT Products Apply to 3C Electronics Assembly: Full-Process Detection & Control Solution for Cabinet-Type Dual-Spindle Auto Screwdriving Machines

  • time:2026-11-16 16:36:45
  • Click:0

Automated screwdriving machines continuously execute feeding, vacuum pickup, transfer, positioning, fastening, and home reset sequences. By configuring detection signals along the sequence of operations, faults such as screw starvation, part misalignment, low air pressure, and fastening anomalies are halted immediately at the point of occurrence—preventing defective assemblies from advancing downstream.

ChatGPT 图像 2026年11月16日 16_33_35

  • 01 Screw Feeding & Counting

  • 02 Product Positioning

  • 03 Safety Interlocking

  • 04 Fastening Verification

01 / DETECTION CHECKPOINT

Piece-by-Piece Screw Feeding Verification

Because micro-screws are small and drop at high speeds, the detection point must combine ultra-fast response times with a compact footprint suited for tight installation spaces.

Detection LocationConfigured ComponentsControl Function
Screw Drop ChuteFiber Optic Amplifier + Through-Beam Fiber Optic SensorOutputs a signal whenever a screw interrupts the light beam, enabling pass-through counting, feed confirmation, and jam detection assistance.

02 / DETECTION CHECKPOINT

Initiating Fastening Only After Proper Fixture Seating

Actuating the screwdriver bit before the housing is fully seated in the fixture easily leads to off-center driving, stripped threads, and scrapped enclosures.

Detection LocationConfigured ComponentsControl Function
Product FixtureUltra-Compact Laser Photoelectric SensorAims a pinpoint light spot at a designated feature on the housing; authorizes clamping and fastening actions only after confirming proper seating.

03 / DETECTION CHECKPOINT

Establishing Safety Protection at Operator Access Openings

Because manual loading and unloading zones sit close to clamping mechanisms and moving axes, hazardous motion must be immediately restricted whenever an operator enters the area.

Detection LocationConfigured ComponentsControl Function
Manual Loading/Unloading OpeningSafety Light Curtain + Safety Control CircuitTriggers an immediate safety stop when hands interrupt the optical beams; protective height, beam pitch, and safety distance are determined via formal risk assessment.

04 / DETECTION CHECKPOINT

Verifying Screw Position Post-Fastening

Verifying both screw presence and head height provides an independent confirmation signal for fastening quality.

Detection LocationConfigured ComponentsControl Function
Fastening PositionFiber Optic Amplifier + Diffuse / Through-Beam Fiber Optic SensorDetects screw presence and verifies whether the screw head sits at the target height, helping identify missing screws and floating (under-driven) screws.

Note: Fiber optic sensing verifies screw presence and physical position; process parameters such as fastening torque and turn count should be monitored in conjunction with signals from the electric screwdriver controller.

CONTROL CHAIN

Four Detection Points Forming a Complete Sequential Interlock

Detection StageConfigured ComponentsControl Function
FeedingThrough-Beam Fiber Optic SensorConfirms screw passage and provides counting pulses.
PositioningUltra-Compact Laser Photoelectric SensorConfirms the product has entered the fastening position.
SafetySafety Light CurtainTriggers a safety stop if personnel enter the hazard zone.
ResultDiffuse / Through-Beam Fiber Optic SensorVerifies screw presence and head seating height.

The PLC executes operations strictly on a "verify-before-release" sequence. Whenever any critical detection signal is unmet, the machine halts at the current step and triggers a corresponding alarm—allowing operators to immediately pinpoint the fault.

Selection Note: Exact models, sensing distances, response speeds, output configurations, and safety categories must be confirmed based on screw dimensions, machine cycle time, fixture clearance, stopping time, and control interfaces.

SOLUTION VALUE

Halting Anomalies Right Where They Occur

From screw drop to final fastening, every critical action has independent sensor feedback. Integrating these detection signals into PLC interlocking shortens troubleshooting time and reduces the risk of missed screws, dry-driving, and defective parts moving downstream.

Recommended products

×

Contact us

I agree to the Privacy Policy and consent to the processing of my personal information for responding to my inquiry.